Hi, I'm attempting to modify the basic firmware, and I'm progressing quite well however there are a couple of sneaky scenarios which require a lower level debugging capability. Can you please advise how you debug the firmware, on the device? I've modified the firmware to call 'AudioMoth_setupSWOForPrint' at the end of AudioMoth_initialise() and added a couple of debug statements such as printf("Debugging enabled"); Throughout the code, being executed. These changes, along with my other alterations were then successfully flashed to the AudioMoth device. I've then connected my J-Link debug probe https://www.segger.com/products/debug-probes/j-link/ , which appears to support the EFM32WG980F256 chip. https://www.segger.com/downloads/supported-devices.php 1. PC -> USB -> AudioMoth USB plug (normal USB connection for an AudioMoth) 2. PC -> USB -> JLink Debug Probe -> SWD via Dupont Connectors -> AudioMoth Debug pads Here's a couple of photos to highlight what I'm doing. Sure, those connections are soldered a little rough but have been verified to be fine. As a simple dump, here's what I'm using. I'm expecting you're doing something similar when modifying the firmware. JLinkExe
SEGGER J-Link Commander V6.52c (Compiled Oct 11 2019 15:44:58)
DLL version V6.52c, compiled Oct 11 2019 15:44:50
....
Type "connect" to establish a target connection, '?' for help
J-Link> connect
Please specify device / core. <Default>: EFM32WG980F256
Type '?' for selection dialog
Device>
Please specify target interface:
J) JTAG (Default)
S) SWD
T) cJTAG
TIF> S
Specify target interface speed [kHz]. <Default>: 4000 kHz
Speed>
Device "EFM32WG980F256" selected.
Connecting to target via SWD
Found SW-DP with ID 0x2BA01477
Scanning AP map to find all available APs
AP[1]: Stopped AP scan as end of AP map has been reached
AP[0]: AHB-AP (IDR: 0x24770011)
Iterating through AP map to find AHB-AP to use
AP[0]: Core found
AP[0]: AHB-AP ROM base: 0xE00FF000
CPUID register: 0x410FC241. Implementer code: 0x41 (ARM)
Found Cortex-M4 r0p1, Little endian.
FPUnit: 6 code (BP) slots and 2 literal slots
CoreSight components:
ROMTbl[0] @ E00FF000
ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7
ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT
ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB
ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM
ROMTbl[0][4]: E0040000, CID: B105900D, PID: 003BB923 TPIU-Lite
ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM
Cortex-M4 identified.
J-Link> SWORead
0 bytes read (0 bytes in host buffer)
J-Link> SWOView
Receiving SWO data @ 4000 kHz.
Data from stimulus port 0:
-----------------------------------------------
Occasionally I'll get SWO output, but its all garbled and meaningless. On other hardware I would think this was a mismatch of the receiving clock (4000 kHz), but maybe I'm attacking this incorrectly. I appreciate this is getting down into the lower levels of core programming on the device but I suspect other users may wish to also understand these debugging aspects when modifying the firmware to suit their needs also. Without a device level debugging capability the only way to check out changes is to flash the device with extra LED flashes to highlight state changes, or log to the microSD via the AudioMoth_appendFile operation. Which SWO debug probe do you use to validate changes to the base firmware? What code changes do you make to enable debugging? Are there Simplicity Studio changes which you utilise to support debugging on the device? Are you debugging the code off the device instead, on a PC using a 32-bit ARM emulator or 32-bit x86 target toolchain? Are you implementing Unit Testing on your version of the firmware?
Hi, It's possible to use AudioMoth as the sensor for this. You would need to develop the sensor platform with the 3G modem as a standalone device, and then AudioMoth could communicate with this using the GPIO pins on the top surface of current PCB. The firmware would also need to be extended to implement this functionality. We've done this in Belize in a few trials using LoRa radio. Our development plan for AudioMoth 2 includes the idea of developing a 'dev board' version of AudioMoth that can easily be added onto another sensor platform to implement this type of functionality. Alex
Thanks Alex. I'm not too tech-savvy but I think I get how this could work. I don't know much about LoRa but if could handle the data in real time then it sounds ideal. I also think it should be possible to use the timing of spearated devices in in detecting the shot to triangulate the position of the shooter reasonably accurately, which would be very useful. I guess my problem is that I know what the sysyem woulld need to do and I have a load of ideas about what would be great, but I don't have the knoweldge to know what is possible or how to get it to work! I do however have a perfect test site to determine whether it is possible to set up a simple, cheap and effective real-time monitoring network for firearms-based poaching, in this case rhino poaching in South Africa. So...if anyone is out there who could help please drop me an email :) ahart@glos.ac.uk