©2019 Open Acoustic Devices

Jan 4, 2018

Audiomoth Schematics

6 comments

Edited: Jan 4, 2018

I'm trying to look at the schematics of the Audiomoth board to figure out how I can interface the Audiomoth to an external data-transmitter. Mainly Tx/Rx pins of sorts that can be used with say a cellular board.

 

When I try to look at the schematics here: https://circuithub.com/projects/OpenAcoustics/AudioMoth/revisions/11676o , there is no preview, and the link to the file leads to a non-working site/access denied :

https://circuithub-static1.s3.amazonaws.com/eda-export%2F11676%2Fp001-schematic-preview.svg?Expires=1515054600&AWSAccessKeyId=AKIAIOFK2M73UL73X4XA&SignatureMethod=HmacSHA256&Signature=YMrY4j12U1%2FK56ItQErIsQHeXGQ%3D

 

Kindly help..

 

Thank you, Abhi

Jan 5, 2018

Hi Andy,

Thanks for fixing it, this was the same link i used earlier..

 

Cheers

Abhi

Jan 8, 2018

Hi Andy, on the above link, the board tab fails to load and says "an error has occured" - tried under chrome and firefox but same error

Jan 8, 2018

Can you try again? You may have caught CircuitHub on an update. The link is working for me.

Jan 8, 2018

Andy, yup all works now so looks like it was just updating

Jan 10, 2018

There is an unpopulated header on the the top of the AudioMoth that is connected to GND, 3V3 and four GPIO pins. This is the easiest way to connect additional sensors or an external radio module.

New Posts
  • Hi, in all my recordings there's a "clicking" noise (26-28kHz). This is an issue that I had before with some recordings but now the noise is louder and it is present in all recordings. The batteries are Energizer AA (new) and the SD card is the SanDisk Extreme 32GB. Is there Anything I can do to make the "clicking" noise disappear?
  • Amazing work! https://www.openacousticdevices.info/mmoth Clearly it is early days, but obviously so many questions pop into mind ... - Off board Lithium ion battery, with a onboad connecter? (So you can choose any size LiOn? or LiPo? like - https://hobbyking.com/en_us/turnigy-2000mah-1s-1c-lipoly-w-2-pin-jst-ph-connector.html ?) - Any Battery life / runtime estimates vs AM1.1? - Cost? Double side so more expensive? - etc, etc, etc ... Anything else to share with us yet??
  • Hi, I'm attempting to modify the basic firmware, and I'm progressing quite well however there are a couple of sneaky scenarios which require a lower level debugging capability. Can you please advise how you debug the firmware, on the device? I've modified the firmware to call 'AudioMoth_setupSWOForPrint' at the end of AudioMoth_initialise() and added a couple of debug statements such as printf("Debugging enabled"); Throughout the code, being executed. These changes, along with my other alterations were then successfully flashed to the AudioMoth device. I've then connected my J-Link debug probe https://www.segger.com/products/debug-probes/j-link/ , which appears to support the EFM32WG980F256 chip. https://www.segger.com/downloads/supported-devices.php 1. PC -> USB -> AudioMoth USB plug (normal USB connection for an AudioMoth) 2. PC -> USB -> JLink Debug Probe -> SWD via Dupont Connectors -> AudioMoth Debug pads Here's a couple of photos to highlight what I'm doing. Sure, those connections are soldered a little rough but have been verified to be fine. As a simple dump, here's what I'm using. I'm expecting you're doing something similar when modifying the firmware. JLinkExe SEGGER J-Link Commander V6.52c (Compiled Oct 11 2019 15:44:58) DLL version V6.52c, compiled Oct 11 2019 15:44:50 .... Type "connect" to establish a target connection, '?' for help J-Link> connect Please specify device / core. <Default>: EFM32WG980F256 Type '?' for selection dialog Device> Please specify target interface: J) JTAG (Default) S) SWD T) cJTAG TIF> S Specify target interface speed [kHz]. <Default>: 4000 kHz Speed> Device "EFM32WG980F256" selected. Connecting to target via SWD Found SW-DP with ID 0x2BA01477 Scanning AP map to find all available APs AP[1]: Stopped AP scan as end of AP map has been reached AP[0]: AHB-AP (IDR: 0x24770011) Iterating through AP map to find AHB-AP to use AP[0]: Core found AP[0]: AHB-AP ROM base: 0xE00FF000 CPUID register: 0x410FC241. Implementer code: 0x41 (ARM) Found Cortex-M4 r0p1, Little endian. FPUnit: 6 code (BP) slots and 2 literal slots CoreSight components: ROMTbl[0] @ E00FF000 ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 000BB00C SCS-M7 ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 003BB002 DWT ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 002BB003 FPB ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 003BB001 ITM ROMTbl[0][4]: E0040000, CID: B105900D, PID: 003BB923 TPIU-Lite ROMTbl[0][5]: E0041000, CID: B105900D, PID: 000BB925 ETM Cortex-M4 identified. J-Link> SWORead 0 bytes read (0 bytes in host buffer) J-Link> SWOView Receiving SWO data @ 4000 kHz. Data from stimulus port 0: ----------------------------------------------- Occasionally I'll get SWO output, but its all garbled and meaningless. On other hardware I would think this was a mismatch of the receiving clock (4000 kHz), but maybe I'm attacking this incorrectly. I appreciate this is getting down into the lower levels of core programming on the device but I suspect other users may wish to also understand these debugging aspects when modifying the firmware to suit their needs also. Without a device level debugging capability the only way to check out changes is to flash the device with extra LED flashes to highlight state changes, or log to the microSD via the AudioMoth_appendFile operation. Which SWO debug probe do you use to validate changes to the base firmware? What code changes do you make to enable debugging? Are there Simplicity Studio changes which you utilise to support debugging on the device? Are you debugging the code off the device instead, on a PC using a 32-bit ARM emulator or 32-bit x86 target toolchain? Are you implementing Unit Testing on your version of the firmware?
Before posting, be sure to check the FAQ.